VORTEX VIPER RED DOT INSTALL
Install the EGW Sight Mount in the dovetail Red Dot Mounting Plate Installation Instructions You can take our mount off and replace your rear sight at any time. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight.
Glock 48 (Our mount is wider than the slide, but it will still work)ĭoes not fit ANY/ALL Glock slides that are already cut for optics.Glock 43x (Our mount is wider than the slide, but it will still work).Glock 43 (Our mount is wider than the slide, but it will still work).Glock 42 (Our mount is wider than the slide, but it will still work).Glock 36 (Our mount is wider than the slide, but it will still work).This mount fits all generation Glocks with only rear sight dovetail cuts (including but not limited to): The dovetail has a progressive taper to allow for easier install. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.Īre you looking to replace your factory Glock rear sight with a red dot mounting plate? Our red dot adapter plates for Glocks easily let you mount your red dot to your gun with no modifications to the slide! Our Glock red dot sight mounts are meant to be installed from the left to the right. These dots may not fit properly on the posts on the plate. Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. *All ADE mounts require 6-32 x 3/8" screws.
VORTEX VIPER RED DOT HOW TO
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.Ĭlick here to see a video from Vortex on how to install our red dot base on a slide.The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench. This product should be installed and checked by a qualified gunsmith. Modification of your firearm may nullify the manufacturer's warranty. The screws that are included with this mount require a 5/64'' allen wrench for installation.
Apply blue Loctite to the provided mounting screwsĢ Button Head Cap Screws - Provided for Vortex Viper and Venom SightsĢ Flat Head Cap Screws - Provided for Burris FastFire and Docter SightsĢ Flat Head Cap Screws - Provided to mount the Plate to the Dovetail (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Place the red dot sight on the EGW Sight Mount Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. Our Beretta 92 red dot sights mounts are meant to be installed from the left to the right (with the muzzle facing forward). We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.ĭo you need to install a red dot mount on your Beretta 92? Our red dot mount allows you to easily install a red dot on your Beretta. The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.
VORTEX VIPER RED DOT DRIVER
(2) 6-32 x 5/16" Flat Head Screws - To Secure Plate to Insert - Requires 5/64 Wrench or Driver (2) 6-32 x 3/8" Flat Head Screws - Requires 5/64 Wrench or Driver (2) 6-32 x 5/16" Button Head Screws - Requires 5/64 Wrench or Driver